Gain extra benefits by becoming a Supporting Member Click here find out how!
Classic Performance Products Classic Parts
Ciadella InteriorsAmerican Auto Wire Classic Industries
Chevs of the 40sDanchuk Catalog
Hellwig Products IncPerformance Rod & CustomEcklers AutoMotive
Nu-Relics Power WindowsRain Gear Wiper Systems
Impala Bob's Bob's Chevy Trucks Bob's Chevelle Parts Bob's Classic Chevy



Username Post: Rear Axle Housing Travel        (Topic#353819)
SandDabMcSkeg 
Poster
Posts: 89

Loc: Coos Bay, Oregon
Reg: 01-04-18
11-08-18 04:50 PM - Post#2750813    

Anyone know how far rearward the rear axle housing travels as stock springs and shocks flex? On open driveline.



Edited by SandDabMcSkeg on 11-08-18 10:10 PM. Reason for edit: No reason given.

 

Chevs of the 40s

Shepherd 
Frequent Contributor
Posts: 1502

Loc: Lake George, NY
Reg: 11-11-15
11-08-18 06:33 PM - Post#2750830    
    In response to SandDabMcSkeg

Stock torque tube driveline?



 
SandDabMcSkeg 
Poster
Posts: 89

Loc: Coos Bay, Oregon
Reg: 01-04-18
11-08-18 10:09 PM - Post#2750846    
    In response to Shepherd

Should have specified, on open driveline.




Edited by SandDabMcSkeg on 11-08-18 10:10 PM. Reason for edit: No reason given.

 
40grit 
Contributor
Posts: 397
40grit
Age: 73
Loc: Chattanooga, Tn
Reg: 07-08-13
11-09-18 02:47 AM - Post#2750856    
    In response to SandDabMcSkeg

Normal rule of thumb is to leave at least 3/4" for travel in the slip yoke at the transmission if that helps any.

John

Just Slightly Abrasive


 
tommy49 
"4th Year" Silver Supporting Member
Posts: 2439
tommy49
Loc: Kaleva, Michigan
Reg: 09-28-12
11-09-18 08:18 AM - Post#2750877    
    In response to SandDabMcSkeg

I don't think there would be any significant rearward "swing" movement at all. The forward spring bolt is the pivot point. Remove the shocks, hang a plumb-bob from the housing and mark the floor. Jack the rear axle all the way up and mark the floor again. That will tell you what the rearward travel is. The total angle travel probably isn't more than 12 degrees. I went through something this when I put in new bump stops.

Tommy

49 Deluxe Sport Coupe, 55 235, 700r4, Blazer rear axle, 4 wheel power disc brakes.

https://www.flickr.com/photos/tommyfortynine /album...



 
40grit 
Contributor
Posts: 397
40grit
Age: 73
Loc: Chattanooga, Tn
Reg: 07-08-13
11-09-18 08:36 AM - Post#2750879    
    In response to tommy49

  • tommy49 Said:
I don't think there would be any significant rearward "swing" movement at all. The forward spring bolt is the pivot point. Remove the shocks, hang a plumb-bob from the housing and mark the floor. Jack the rear axle all the way up and mark the floor again. That will tell you what the rearward travel is. The total angle travel probably isn't more than 12 degrees. I went through something this when I put in new bump stops.



Until I read Tommy's post, I didn't realize I misread the origional post. I agree. The rearward movement is margional but as the leaf spring straightens out there will be a limited amount.

His suggestion to mark the floor with the weight both on and off the spring should answer the question.

I apologize for answering a question that was not asked.

John

Just Slightly Abrasive


 
SandDabMcSkeg 
Poster
Posts: 89

Loc: Coos Bay, Oregon
Reg: 01-04-18
11-09-18 08:54 AM - Post#2750883    
    In response to 40grit

I am concerned about clearance between a new gas tank and the differential, (station wagon) we are using one from a 55-56 wagon because they are bigger capacity, the 51 is only 12 gallons.



 
DanD1950 
"3rd Year" Silver Supporting Member
Posts: 870
DanD1950
Loc: London Ont. Canada
Reg: 10-16-11
11-09-18 02:42 PM - Post#2750913    
    In response to SandDabMcSkeg

If you have at least a 1/2 inch clearance with the car sitting static; the diff should never hit the fuel tank. If it does, check the front bushings of the leaf springs. Spring wrap will allow the dif to rotate; but it will not allow rearward movement.

Dan.

50 Styleline Deluxe, 2 Door Sedan, Was a 216cu", Three Speed Manual. She now has a 4.8Lt V8 LR4 injected engine, 4L60E 4 speed automatic, 10 bolt diff 342 gear with an Eaton C80 Locker



 
Mike JW 
"6th Year" Gold Supporting Member
Posts: 1331
Mike JW
Loc: Arroyo Grande, CA
Reg: 01-19-06
11-09-18 07:06 PM - Post#2750941    
    In response to DanD1950

If your going with stock springs,and a V8 motor you may want to put some different springs in the rear. The stock springs were designed to be used with the torque tube. Without the torque tube you'll get a lot of spring wrap.



 
SandDabMcSkeg 
Poster
Posts: 89

Loc: Coos Bay, Oregon
Reg: 01-04-18
11-12-18 03:22 PM - Post#2751186    
    In response to Mike JW

What exactly is spring wrap? And if I replaced the springs, what is a good replacement?




 
Shepherd 
Frequent Contributor
Posts: 1502

Loc: Lake George, NY
Reg: 11-11-15
11-12-18 03:43 PM - Post#2751189    
    In response to SandDabMcSkeg

Spring wrap up happens when accelerating from a dead stop, the forward section of the spring kind of winds upwards as a result of engine torque. This must be avoided either with antiwrap traction bars or stiffer front section of the rear spring or additional spring clamps, of course the torque tube prevents this.



 

Chevs of the 40s

Icon Legend Permissions Topic Options
Report Post

Quote Post

Quick Reply

Print Topic

Email Topic

281 Views
FusionBB
FusionBB™ Version 2.1
©2003-2006 InteractivePHP, Inc.
Execution time: 0.1 seconds.   Total Queries: 17   Zlib Compression is on.
All times are (GMT -0800) Pacific. Current time is 04:44 PM
Top