Select "print" from your browser's "File" menu.

Back to Post
Username Post: Repair Panel Comparisons
kck71
Poster
Posts 93
07-21-21 04:37 AM - Post#2823607    

Hello, just looking for some opinions on the quality of repair panels available from different suppliers. I see that EMS, Filling Station, Chevs of the 40s, NCA all seem to sell similar pieces for 53-54 cars. However, prices do vary some between them all. For example, the online store for EMS has prices higher than that of the Filling Station.

Are these sellers all getting the same parts from the same manufacturer? Or is there actually a wide range of quality differences between EMS and others?
1957 Two-Ten 4-door Sedan
1953 Bel Air 4-door Sedan
1959 3800 Pickup

Does it still count as a "barn find" when it's your barn?

drtyler
"6th Year" Gold Supporting Member
Posts 620
07-21-21 06:03 AM - Post#2823611    

I would verify with the vendor first for the particular panel you need. I believe most of the vendors carry EMS panels. The EMS panels are generally rated pretty well. If you need full floors, there was a non-EMS set (Golden Star?) that seemed to be good fit and quality. Check some of the build threads.

Also, check the cost of shipping. I know Filling Station and Chevs of the 40s can get pretty high on shipping costs. I believe if you order from EMS there is no extra charge for shipping, although this policy may have changed. So the part cost may be a bit more, but it also includes shipping.


eplantage
Frequent Contributor
Posts 2473
07-21-21 06:56 AM - Post#2823614    

I know that EMS actually manufactures what they are selling. The EMS guy actually stopped at my place a few years ago and measured up my convertible doors for replacement panels. I'm not sure who else is actually making them. Some are just resellers. I bought the rear trunk brace from an Ebay seller, it was shipped from NCA, but was made by EMS. NOS panels are the best fit if you can find them but even then may require some tweaking.
Age: 67 at the moment
1950 Chevrolet Sedan Delivery
1953 BelAir Convertible Project
2002 Heritage Springer FLSTSI
1930 Model A Standard Coupe

mahlmann
"11th Year" Gold Supporting Member
Posts 1829
mahlmann
07-21-21 07:27 AM - Post#2823616    

I used EMS wheel arch and rear lower quarter panels to repair our '50 tin woody station wagon. The shop that did the work said the panels fit pretty good and needed minimal rework to apply. The repairs turned out very nice.
Mike Ahlmann
Las Cruces, NM
'50 Tin Woodies (two) Ramon and Willard
'58 Impala Sport Coupe
'69 El Camino SS-396
'07 Ford F150 to haul parts for above
'16 Ford Explorer 3.5 EcoBoost - Red Rocket

EMS Customer Service
Thread Sponsor
Posts 182
07-23-21 07:40 PM - Post#2823785    

as for pricing some of dealer have not updated there web sites with new pricing but do it after the order is made,

the ems online site keeps updated

the pricing problem is rapidly rising steel prices, up 130% since election day

there will be another price increase in mid august to 13% above published 2020 prices ( 10% now)

we are being told there may be up another 40% rise by the end of the year.

if your not sure of your local supplier: 1). ems will allways put a label with our name and phone number. --no label- then not ems

or you can use our online system or call direct (often busy)

thanks to all who have bought from us--the ems guy

ALL SO CHECK OUT OUR VIDEO'S ON YOU TUBE WHERE YOU CAN SEE THE PARTS. UNDER "EMSAUTOMOTIVE"
Cruzin Okie
"6th Year" Silver Supporting Member
Posts 748
Cruzin Okie
07-25-21 07:14 PM - Post#2823894    

I bought cheaper floor pans and a toe boards for my 1953 210. After struggling with them trying to get them to fit properly I threw them aside and bought EMS. They Matched the contours of the floor and mated up perfectly. The EMS made my project so much easier.
Johnnie

1950 styleline deluxe sports coupe, 350 cid, TH 400, nova rear end. Gen IV Vintage air. SOLD!
1953 210 4 Door, 235 with Powerglide. All original except for the 1954 hood bird.

John 3:16


Franks_Old_53
"3rd Year" Silver Supporting Member
Posts 138
Franks_Old_53
08-07-21 05:04 PM - Post#2824704    

Except for my floor pan and trunk pan, every other piece I used on my car was EMS. Every one of those panels was VERY high quality. The metal is thick and the stamping quality is very good (not perfect but VERY good).

I had to use a full floor pan, I believe that it was Gold Star. Very pleased with it as well.

You can look at my project page for the link and can see how the panels look after install.

Best of luck with your project!

David

Accountant by profession, wanna-be car restorer by choice

Rebuilding my Granddad's 1953 Chevy 150 https://www.chevytalk.org/fusionbb/showtopic.php?t...

EMS Customer Service
Thread Sponsor
Posts 182
08-12-21 01:40 AM - Post#2824978    

thanks for for buying from ems, we try to our best for everyone

the ems guy
FusionBB
FusionBB™ Version 2.1
©2003-2006 InteractivePHP, Inc.
Execution time: 0.071 seconds.   Total Queries: 14   Zlib Compression is on.
All times are (GMT -0800) Pacific. Current time is 12:52 AM
Top